how to make a bamboo wind chime

How to Make a Bamboo Wind Chime.

Wind chimes, a decorative piece that can liven up your home, can be made from a variety of materials such as ceramic pieces and metal tubing. If you are going for a natural look and mellow tone, bamboo is an excellent material to use. You can make a simple project out of creating your own bamboo wind chime by following the steps below.

Method 1 Making a Bamboo Wind Chime.
1. Find some bamboo. If you are lucky, bamboo may already be growing wild in your area, and it is simply a matter of obtaining permission and cutting the bamboo plant to a proper size. If there is no local source, you may be able to purchase a common bamboo pole, used for fishing. You can also often find bamboo poles of varying sizes at garden supply stores.
Make sure your bamboo is thoroughly seasoned and is not split or rotten.
2. Cut the bamboo into six lengths. Each length should be composed of two of the plant's "sections", with one end above the partition-like segment end, and the other below it, so you have an open tube to work with.
3. Split the hollow end of each piece. This can be done with a very sharp knife, but care must be used, since both the splinters from the bamboo and the knife can impale or cut you. If you have a vice, it might be easier (and less risky) to fix the bamboo in the vice and cut it with a saw, especially if it is quite tough. Taper the last inch (2.5cm) or so off at an angle.
4. Drill 1/8 inch (3mm) holes just above the section on the solid end of each piece, parallel to the cut you made on the opposite end. This will ensure the hollow, concave bamboo "channel" will be facing out on each tube when they are assembled.
5. Cut a round piece of plywood or other material about 7 times the diameter of the average piece of bamboo. In the photos, each piece was about 1 inch in diameter, so the plywood disk is 7 inches (~18cm).
6. Lay out the disk into 6 equal spaces around the circumference, then drill a 1/8 inch (3mm) hole about 3/4 inch (~2cm) on either side of the layout marks, near the edge of the disk.
7. Thread a piece of string through one of the holes, and tie off one end. The string should be about 48 inches (1.2m) long to begin with; any surplus can be cut off after each tube is tied in place. Heavyweight fishing line can be used for hanging the tubes, as in the photos, but a more flexible string will give better results.
8. Thread your string through the holes in the end of one bamboo section, then back through the hole in the plywood on the other side of your layout mark. Continue doing this until each bamboo is hanging under the plywood disk, then tie off the end of your line.
9. Adjust the individual sticks so that each one is staggered higher or lower than the adjacent one. This is what changes the tone of each bamboo, so you can experiment here until you obtain a pleasant sound with the tonal variation you desire.
10. Drill three holes about 1 1/2 inches (3.8cm) from the center of your plywood disk, equally spaced around it. Measure and cut three equal lengths of string, about 30 inches (0.75m) long, and tie them together on one end, allowing a small loop to be formed.
READ MORE futuristichomedecor.blogspot.com
(This article based on www.wikihow.com)
Note :
Acknowledgements
This presentation contains images that were used under a Creative Commons License. Click here to see the full list of images and attributions:
link.attribute.to/cc/485281

Home decor ideas,Decoration ideas,DIY for home,Creative decor tips,Home hacks,Decor hacks,home decor,Decor ideas,Room decor,Interior design,Wall decor,House,Home,Decor,Home craft ideas,DIY home decor,Diy room decor,romantic decor,DIY home decorating idea,DIY home decorating,Indoor decor ideas,room decor ideas,home decor,interior design,diy home design ideas, home decor, decor, home decor ideas, projects, handmade, room decorating ideas, decoration, decoration home,decoration ideas, home design, home decoration ideas, wall decoration ideas,