Playback starts YouTube’s embedded player (privacy-enhanced mode).
How to make simple High Voltage traveling Arc (JACOB’S LADDER) with ZVS Flyback Trafo
ChannelMirko PavleskiDescription from the creator
A Jacob's ladder is a wonderful exotic-looking display of electric white, yellow, blue or purple arcs.
The Arc starts from the narrowest point and ionizes and heats the air causing it to rise. This ionized air forms the path of least resistance. As it risees the arc follows along. When the ionized air reaches the top of the electrodes and continues to rise, the arc becomes too long for the voltage and breaks up . After the acrc breaks up at the top , the electrode voltage rises again. Another arcs forms at the narrowest point.
The video above describes how to make such a device using an electronic circuit known as Mazzilli ZVS flyback driver. You can download schematic diagram at the link below. It consists of two or four power Mosfet transistors (e.g.IRF530, IRFP240,irfz44,P65NF06 or similar) and several additional components that form a relaxation oscillator called Royer Oscillator , named after its inventor. The primary contains five windings of insulated wire with a diameter of 2.5mm^2 wound on the ferrite core of a flyback transformer from an old CRT monitor or TV.
The flyback trafo secondary is connected with the rods bent so one point near the bottom of the wires is very close (1/4" to 1/2"). The arc will strike at the closest part, then the heat will make it rise.
The device is powered by 12V Power Supply from old Server Computer.The power supply must provide a minimum 10 Ampers of current.
Please note: A traveling-arc device is very dangerous. The spark can burn through paper and plastic and start fires. Contact with the high-voltage conductors can be lethal even if the high voltage power supply originates from a battery.
You can download Shematic Diagrams at:
snipboard.io/yr5lc1.jpg
snipboard.io/x0W2BS.jpg
If you are interested in this area, look at the Playlist with all my High Voltage projects at:
youtube.com/playlist?list=PLAxrqEdgtyUV5SriPejN…
Visit my Youtube Channel for more Projects , DIY and How To Make videos:
youtube.com/c/MirkoPavleskiMK/videos
by mircemk
SUBSCRIBE LIKE AND SHARE !!!!
Thanks for your Support !
Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: youtu.be/EwRdKJURDHw
#NoCopyrightMusic #VlogMusic #VlogNoCopyrightMusic
The Arc starts from the narrowest point and ionizes and heats the air causing it to rise. This ionized air forms the path of least resistance. As it risees the arc follows along. When the ionized air reaches the top of the electrodes and continues to rise, the arc becomes too long for the voltage and breaks up . After the acrc breaks up at the top , the electrode voltage rises again. Another arcs forms at the narrowest point.
The video above describes how to make such a device using an electronic circuit known as Mazzilli ZVS flyback driver. You can download schematic diagram at the link below. It consists of two or four power Mosfet transistors (e.g.IRF530, IRFP240,irfz44,P65NF06 or similar) and several additional components that form a relaxation oscillator called Royer Oscillator , named after its inventor. The primary contains five windings of insulated wire with a diameter of 2.5mm^2 wound on the ferrite core of a flyback transformer from an old CRT monitor or TV.
The flyback trafo secondary is connected with the rods bent so one point near the bottom of the wires is very close (1/4" to 1/2"). The arc will strike at the closest part, then the heat will make it rise.
The device is powered by 12V Power Supply from old Server Computer.The power supply must provide a minimum 10 Ampers of current.
Please note: A traveling-arc device is very dangerous. The spark can burn through paper and plastic and start fires. Contact with the high-voltage conductors can be lethal even if the high voltage power supply originates from a battery.
You can download Shematic Diagrams at:
snipboard.io/yr5lc1.jpg
snipboard.io/x0W2BS.jpg
If you are interested in this area, look at the Playlist with all my High Voltage projects at:
youtube.com/playlist?list=PLAxrqEdgtyUV5SriPejN…
Visit my Youtube Channel for more Projects , DIY and How To Make videos:
youtube.com/c/MirkoPavleskiMK/videos
by mircemk
SUBSCRIBE LIKE AND SHARE !!!!
Thanks for your Support !
Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: youtu.be/EwRdKJURDHw
#NoCopyrightMusic #VlogMusic #VlogNoCopyrightMusic
About this tutorial
Mirko Pavleski published this 5:33 video tutorial on August 3, 2020. It has been watched 3,677 times on YouTube.
- Channel
- Mirko Pavleski
- Category
- Science & Technology
- Duration
- 5:33
- Published
- August 3, 2020
- Views
- 3,677
- Likes
- 54
Tags
Share
This tutorial in other languages
- FRComment faire simple, haute tension Arc voyage (JACOB ÉCHELLE) avec ZVS Flyback Trafo
- ESComo hacer sencilla de alto voltaje que viaja Arco (DE ESCALA DE JACOB) con ZVS Flyback Trafo
- PTComo fazer simples High Voltage viajar Arc (DA ESCADA JACOB) com ZVS Flyback Trafo
- ITCome rendere semplice ad alta tensione che viaggiano Arc (JACOB'S LADDER) con ZVS Flyback Trafo
- DEWie man einfache High Voltage Reisen Arc (Himmelsleiter) mit ZVS Flyback Trafos machen
- NLHoe maak je eenvoudig High Voltage reizen Arc (Jacob's Ladder) met ZVS Flyback Trafo
- RUКак сделать простой Высоковольтное путешествие Arc (Джейкоб лестница) с ZVS строчного TRAFO
- PLJak zrobić prosty High Voltage podróżowanie łuku (Jakubowa Drabina) z ZVS Flyback Trafo
- JAシンプルな高電圧がZVSフライバックTrafoとアーク(JACOB'S LADDER)を旅行にする方法
- ARكيفية جعل بسيطة الجهد العالي السفر قوس (يعقوب LADDER) مع ZVS فلايباك TRAFO
- HIकैसे सरल उच्च वोल्टेज ZVS Flyback Trafo साथ आर्क (जैकब्स लैडर) यात्रा करने के लिए
- IDCara membuat sederhana Tegangan Tinggi bepergian Arc (JACOB'S TANGGA) dengan ZVS Flyback Trafo