Playback starts YouTube’s embedded player (privacy-enhanced mode).
How to Make an Atlatl
ChannelHowcastDescription from the creator
Full Playlist: youtube.com/playlist?list=PLLALQuK1NDrj4VP2ZSv1…
-
-
Watch more Wilderness Survival Skills videos: howcast.com/videos/329061-How-to-Make-an-Atlatl
The atlatl revolutionized early hunting practices by greatly increasing the speed of spears. You can construct a functional atlatl using these steps.
Step 1: Sand the wood
Sand the wood base until it is smooth.
Step 2: Drill a hole
Drill a ⅜-inch diameter hole at a 135-degree angle to, and about 1¾ inches from, the end of the wood base. Drill deeply without going all the way through the wood.
Step 3: Insert the dowel in the hole
Round off one end of the dowel peg with the utility knife, squeeze glue into the hole in the base, and place the flat end of the dowel peg in it. Move it around in the hole to spread the glue, and then push it all the way in.
Step 4: Attach the sinew to the peg
Tie a slip knot in each piece of sinew, forming 3-inch loops, place one of the loops over the base of the peg, and pull it tight. Wrap the sinew around the base of the peg to hold it securely in place and then glue the sinew down.
Step 5: Glue the strap
Apply glue to both sides of the stick, about 7 inches from the handle end. Place the two ends of the leather strap in the glue.
Tip
The leather handle is positioned on the side of the atlatl opposite the peg, with the strap ends attached to the adjoining two sides.
Step 6: Wrap the ends of the strap with sinew
Wrap the ends of the leather strap with the second piece of sinew, starting about ¼ inch from the ends. Wrap the strap tightly as you move toward the handle end and secure the sinew in place with glue.
Did You Know?
Atlatl is the Aztec word for spear thrower.
-
-
Watch more Wilderness Survival Skills videos: howcast.com/videos/329061-How-to-Make-an-Atlatl
The atlatl revolutionized early hunting practices by greatly increasing the speed of spears. You can construct a functional atlatl using these steps.
Step 1: Sand the wood
Sand the wood base until it is smooth.
Step 2: Drill a hole
Drill a ⅜-inch diameter hole at a 135-degree angle to, and about 1¾ inches from, the end of the wood base. Drill deeply without going all the way through the wood.
Step 3: Insert the dowel in the hole
Round off one end of the dowel peg with the utility knife, squeeze glue into the hole in the base, and place the flat end of the dowel peg in it. Move it around in the hole to spread the glue, and then push it all the way in.
Step 4: Attach the sinew to the peg
Tie a slip knot in each piece of sinew, forming 3-inch loops, place one of the loops over the base of the peg, and pull it tight. Wrap the sinew around the base of the peg to hold it securely in place and then glue the sinew down.
Step 5: Glue the strap
Apply glue to both sides of the stick, about 7 inches from the handle end. Place the two ends of the leather strap in the glue.
Tip
The leather handle is positioned on the side of the atlatl opposite the peg, with the strap ends attached to the adjoining two sides.
Step 6: Wrap the ends of the strap with sinew
Wrap the ends of the leather strap with the second piece of sinew, starting about ¼ inch from the ends. Wrap the strap tightly as you move toward the handle end and secure the sinew in place with glue.
Did You Know?
Atlatl is the Aztec word for spear thrower.
About this tutorial
Howcast published this 2:05 video tutorial on November 14, 2010. It has been watched 20,986 times on YouTube.