Playback starts YouTube’s embedded player (privacy-enhanced mode).
How to Install a Car Alarm DIY
ChannelBullshitkornerDescription from the creator
Installing a Alarm is not for the Faint of Heart
Viper Alarm amzn.to/3nI30BT
The Viper 3305v Alarm is cheap and has all these features Failsafe starter Disable, Stinger double-guard shock sensors, Revenger shoft-chirp siren, Status LED, Optional keyless Entry Trunk Release output, Includes one 2-Way and one 1-Way 4 button remote. This is basically a how to video if you plan on purchasing this alarm and to install it in your Jeep TJ.
IGNITION INPUT – Needs to see power while the key is in the Run and Crank Position. This was a Blue wire found in my ignition column.
12 VOLT CONSTANT POWER – This I connected to a red and pink wire in the steering column.
GROUND WIRE – Ground where you want somewhere on bare Metal.
HOOD TRIGGER – I Have a Mercury Switch Installed on my hood so I connected it there.
DOOR TRIGGER – I Tied this into the Yellow wire where the footwell light is under the drivers side steering column.
STARTER Disable WIRE -There is a small yellow wire in the steering column as seen in the video this is the wire you need to disconnect.
HOW TO WIRE RELAY – Green Wire connects to Yellow wire running to starter relay. The Black wire is connected to the yellow wire running to the steering column.
This video is how to install a Car alarm in a jeep
DISCLAIMER: Due to factors out of the control of Bullshitkorner and Bsk Garage, we cannot guarantee against improper use or unauthorized modifications of this information. Bullshitkorner and Bsk garage assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video and all other videos produced by Bullshitkorner and Bsk Garage. Use this information at your own risk. Bullshitkorner and Bsk Garage recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Bullshitkorner and Bsk Garage Be safe! This video and description contain affiliate links, which means that if you click on one of the product links, we receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!
#ViperAlarm #Caralarm #alarminstall
Viper Alarm amzn.to/3nI30BT
The Viper 3305v Alarm is cheap and has all these features Failsafe starter Disable, Stinger double-guard shock sensors, Revenger shoft-chirp siren, Status LED, Optional keyless Entry Trunk Release output, Includes one 2-Way and one 1-Way 4 button remote. This is basically a how to video if you plan on purchasing this alarm and to install it in your Jeep TJ.
IGNITION INPUT – Needs to see power while the key is in the Run and Crank Position. This was a Blue wire found in my ignition column.
12 VOLT CONSTANT POWER – This I connected to a red and pink wire in the steering column.
GROUND WIRE – Ground where you want somewhere on bare Metal.
HOOD TRIGGER – I Have a Mercury Switch Installed on my hood so I connected it there.
DOOR TRIGGER – I Tied this into the Yellow wire where the footwell light is under the drivers side steering column.
STARTER Disable WIRE -There is a small yellow wire in the steering column as seen in the video this is the wire you need to disconnect.
HOW TO WIRE RELAY – Green Wire connects to Yellow wire running to starter relay. The Black wire is connected to the yellow wire running to the steering column.
This video is how to install a Car alarm in a jeep
DISCLAIMER: Due to factors out of the control of Bullshitkorner and Bsk Garage, we cannot guarantee against improper use or unauthorized modifications of this information. Bullshitkorner and Bsk garage assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video and all other videos produced by Bullshitkorner and Bsk Garage. Use this information at your own risk. Bullshitkorner and Bsk Garage recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Bullshitkorner and Bsk Garage Be safe! This video and description contain affiliate links, which means that if you click on one of the product links, we receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!
#ViperAlarm #Caralarm #alarminstall
About this tutorial
Bullshitkorner published this 4:38 video tutorial on November 13, 2015. It has been watched 238,911 times on YouTube.
- Channel
- Bullshitkorner
- Category
- Howto & Style
- Duration
- 4:38
- Published
- November 13, 2015
- Views
- 238,911
- Likes
- 756
Tags
Share
This tutorial in other languages
- FRComment faire pour installer un bricolage d'alarme de voiture
- ESCómo instalar una alarma de coche DIY
- PTComo instalar um DIY alarme do carro
- ITCome installare un fai da te Car Alarm
- DEWie man ein Auto Alarm DIY bringen
- NLHoe maak je een Car Alarm DIY installeren
- RUКак установить автосигнализацию DIY
- PLJak zainstalować DIY autoalarm
- JA車の警報DIYをインストールする方法
- ARكيفية تثبيت DIY أجهزة إنذار للسيارة
- HIएक कार अलार्म DIY स्थापित करने के लिए कैसे
- IDCara Menginstal DIY Alarm Mobil